 |
 |
New model includes pattern adjustment knob at front of gun head.
Swivel Side Cup - Perfect design for woodworking
Cup swivels so you can spray in any direction and the cup will stay in the correct position.
Please note* Fuji spray guns can only be used with an HVLP Turbine (any make). They cannot be used with standard compressors. Unless you purchase a conversion regulator.
| #3 Air Cap Water-based Lacquers, Nitrocellulose Lacquer, Sealers, Cellulose, Acrylics, Synthetics, Polyurethane, Stains. |
#4 Pigmented Lacquer and Thinned Latex where finer finish is required. Also ideal for heavy Varnishes, Primers, Oil-Based Paints. |
|
NEW! Gravity HVLP XPC-G GOLD
SGW: This is one fantastic gun. Modern Gravity Design with a new Swivel action. Cup can be moved in a flash to accommodate different spraying angles. Even up and down. A fantastic sprayer highly recommended.
Features
We recommend #3 tip with a 4 stage compressor for fine finishing requires 20%-30% thinning good for sprayable professional coatings. For less thinning and thicker products and consumer grade products like house enamels and brushable products we recommend the #4 tip set.
Fits
ACCUSPRAY, GRACCO, Turbine Air Turbines, for Lexair Please make a note which turbine you are attaching to.
|
|
EXCLUSIVE XPC-G FINE FINISH
2 TIP SGW PACKAGE
Convertible
GRAVITY XPC-G GOLD
SGW PACK
Standard Gravity & Larger 1 Quart Gravity
(same size as the bottom feed gun)
|
| #3 Air Cap Water-based Lacquers, Nitrocellulose Lacquer, Sealers, Cellulose, Acrylics, Synthetics, Polyurethane, Stains. |
#4 Pigmented Lacquer and Thinned Latex where finer finish is required. Also ideal for heavy Varnishes, Primers, Oil-Based Paints. |
-
-
Pressure assisted Gravity Spray Cup side mounted for a smaller footprint and easier maneuverability.
-
Swivel action in the cup allows cup to rate and helps the gun spray at any angle. even up and down.
-
Gun can handle fine finish lacquers and urethanes with #3 tip set as well as heavier paints with the #4 tip set.
-
Easy to use gravity feed design. Screw top for easy filling.
-
Having a smaller capacity cup the GT-X2 is much lighter in weight than the XT-2.
-
Spray gun may be converted to upper hose connect kit.
-
The GT-X2 can be easily changed to pure gravity spray which will give a finer softer spray with lighter finishes.
-
The GT-X2 can be used with a pressure pot.
|
Fuji Spray® developed this new spraygun to meet the rising demand for a gravity gun that can be used with any HVLP turbine. The new Gravity Spray gun has all the features of the standard Fuji XT gun. The GT-X2 comes with the #4 Aircap installed. This is the medium output size, best for fine finishing with lacquers, enamels, polyurethane, latex, water based coatings and more. The Stainless Steel Cup is 400cc (.85 Pint).
**NEW** The cup now uses pressure feed (plus gravity) for faster coverage. It now has the same abilities as our XT-2 spray gun. This spray gun is already proving to be very popular with Bathtub and Auto Refinishers but it is also perfect for cabinet spraying too. Also, please see the 7015 Upper Hose Connector Kit for those who prefer the hose attached to the rear of the barrel.
Cleaning is a snap! The gun does not have to be connected to the hose or turbine. Here’s how…
- Partially fill the cup with solvent
- Wind out the fluid knob and pull the trigger
- Direct the fluid stream into a container
An excellent choice for professional use or even for the serious hobbyist. Sorry... Fuji only manufactures this spray gun with the 400cc size cup
-
|
| |
COMPLETE OUTFITS
  |
|
